Enhancement of the performance surface roughness of wire cutting process by additives Nano [AL2O3]

Azwan Bin Sapit, Saad Kariem Shather, Farook Nehad Abed

Abstract


Experimental investigation and optimization of machining parameters in Wire EDM in terms adding particles Nano-reinforced titanium alloy composite abstracts among the various mechanical processes, the process of manufacturing in wire electrical discharge machines WIRE EDM is one of the most effective and cost-efficient manufacturing processes in the manufacture of titanium alloys Ti-6242. Ti has been dealt with in this article investigate each of operating parameters such as pulse on time, pulse off time, voltage and current insulating liquid with Nano powder [AL2O3] in WIRE EDM compounds titanium alloy. Experiments on titanium alloy carried out with powder mixture with particles size average of [5 nm]. Operating parameters such as voltage, pulse on time and pulse off time are taking into consideration four factors based on the response surface methodology. The performance of thesis evaluated WIRE EDM for ti-6242 using the surface roughness factor SURFACE ROUGHNESS. Quadratic models were developed between parameters and WIRE EDM responses by regression analysis is. The derived mathematical models are then optimized using Box-Behnken optimization based on desire analysis. The search indicates that the expected values of the model obtained to match the experimental values. Improvement in surface roughness is observed in terms of the values obtained from the Box-Behnken analysis.

Full Text:

PDF

References


Vijaya Bhaskar, S., Rajmohan, T., Giri Sesha Sai, G.R., Sandeep Kumar Reddy, G., 2015. Multiple Performance Optimization in WEDM Parameters Using Desirability Analysis. Appl. Mech. Mater. 813–814, 352–356

Poovazhagan, L., Kalaichelvan, K., Sornakumar, T., 2016. Processing and Performance Characteristics of Aluminum-Nano Boron Carbide Metal Matrix Nanocomposites. Mater. Manuf. Process. 31, 1275–1285. https://doi.org/10.1080/10426914.2015.1026354

Poddar, P., Srivastava, V.C., De, P.K., Sahoo, K.L., 2007. Processing and mechanical properties of SiC reinforced cast magnesium matrix composites by stir casting process. Mater. Sci. Eng. A 460–461, 357–364. https://doi.org/10.1016/j.msea.2007.01.052

Nourbakhsh, F., Rajurkar, K.P., Malshe, A.P., Cao, J., 2013. Wire Electro-Discharge Machining of Titanium Alloy. Procedia CIRP 5, 13–18. https://doi.org/10.1016/j.procir.2013.01.003

Wang, Y., Wang, Q., Ding, Z., He, D., Xiong, W., Chen, S., Li, Z., 2018. Study on the mechanism and key technique of ultrasonic vibration and magnetic field complex assisted WEDM-LS thick shape memory alloy workpiece. J. Mater. Process. Technol. 261, 251–265. https://doi.org/10.1016/j.jmatprotec.2018.06.006

Babu Rao, T., Gopala Krishna, A., 2013. Simultaneous optimization of multiple performance characteristics in WEDM for machining ZC63/SiCp MMC. Adv. Manuf. 1, 265–275. https://doi.org/10.1007/s40436-013-0029-y

Bobbili, R., Madhu, V., Gogia, A.K., 2015. Modelling and analysis of material removal rate and surface roughness in wire-cut EDM of armour materials. Eng. Sci. Technol. Int. J. 18, 664–668. https://doi.org/10.1016/j.jestch.2015.03.014

Abbasi, J.A., Jahanzaib, M., Azam, M., Hussain, S., Wasim, A., Abbas, M., 2017. Effects of wire-Cut EDM process parameters on surface roughness of HSLA steel. Int. J. Adv. Manuf. Technol. 91, 1867–1878. https://doi.org/10.1007/s00170-016-9881-9

Bobbili, R., Madhu, V., Gogia, A.K., 2015. Modelling and analysis of material removal rate and surface roughness in wire-cut EDM of armour materials. Eng. Sci. Technol. Int. J. 18, 664–668. https://doi.org/10.1016/j.jestch.2015.03.014

Zhang, C., 2014. Effect of wire electrical discharge machining (WEDM) parameters on surface integrity of nanocomposite ceramics. Ceram. Int. 40, 9657–9662. https://doi.org/10.1016/j.ceramint.2014.02.046

Mandal, A., Dixit, A.R., Chattopadhyaya, S., Paramanik, A., Hloch, S., Królczyk, G., 2017. Improvement of surface integrity of Nimonic C 263 super alloy produced by WEDM through various post-processing techniques. Int. J. Adv. Manuf. Technol. 93, 433–443. https://doi.org/10.1007/s00170-017-9993-x

Wang, Y., Wang, Q., Ding, Z., He, D., Xiong, W., Chen, S., Li, Z., 2018. Study on the mechanism and key technique of ultrasonic vibration and magnetic field complex assisted WEDM-LS thick shape memory alloy workpiece. J. Mater. Process. Technol. 261, 251–265. https://doi.org/10.1016/j.jmatprotec.2018.06.006

Aidoo, A. W. (2019). The impact of access to credit on process innovation. Heritage and

Sustainable Development, ISSN 2712-0554, 1(2), 48-63

Silman, H. K., & Ali, A. E. (2020). Breast cancer identification based on artificial

intelligent System. Sustainable Engineering and Innovation, ISSN 2712-0562, 2(2), 41-49

Thivagar, M. L., Ahmed, M. A., Ramesh, V., & Hamad, A. A. (2020). Impact of non-linear

Electronic circuits and switch of chaotic dynamics. Periodicals of Engineering and

Natural Sciences, 7(4), 2070-2091

Poovazhagan, L., Kalaichelvan, K., Sornakumar, T., 2016. Processing and Performance Characteristics of Aluminum-Nano Boron Carbide Metal Matrix Nanocomposites. Mater. Manuf. Process. 31, 1275–1285. https://doi.org/10.1080/10426914.2015.1026354

Gopal, P.M., Prakash, K.S., Jayaraj, S., 2018. WEDM of Mg/CRT/BN composites: Effect of materials and machining parameters. Mater. Manuf. Process. 33, 77–84. https://doi.org/10.1080/10426914.2017.1279316

Chen, X., Wang, Y., Wang, Z., Liu, H., Chi, G., 2018. Study on Micro Reciprocated Wire-EDM for Complex Indexing Structure. Procedia CIRP 68, 120–125. https://doi.org/10.1016/j.procir.2017.12.033

Myers, R.H., Montgomery, D.C., Anderson-Cook, C.M., 2016. Response Surface Methodology: Process and Product Optimization Using Designed Experiments. John Wiley & Sons.

Thivagar, M. L., & Abdullah Hamad, A. (2020). a theoretical implementation for a

Proposed Hyper- Complex Chaotic System. Journal of Intelligent & Fuzzy Systems 38.

–2590

Nourbakhsh, F., Rajurkar, K.P., Malshe, A.P., Cao, J., 2013. Wire Electro-Discharge Machining of Titanium Alloy. Procedia CIRP 5, 13–18. https://doi.org/10.1016/j.procir.2013.01.003

Rajmohan, K., Kumar, A.S., 2017. Experimental investigation and prediction of optimum process parameters of micro-wire-cut EDM of 2205 DSS. Int. J. Adv. Manuf. Technol. 93, 187–201. https://doi.org/10.1007/s00170-016-8615-3

Vijaya Bhaskar, S., Rajmohan, T., Giri Sesha Sai, G.R., Sandeep Kumar Reddy, G., 2015. Multiple Performance Optimization in WEDM Parameters Using Desirability Analysis. Appl.Mech.Mater.813–814,352–356. https://doi.org/10.4028/www.scientific.net/AMM.813-814.352

Thivagar, L. M., Hamad, A. A., & Ahmed, S. G. (2020). Conforming dynamics in the metric

Spaces. Journal of Information Science and Engineering, 36(3) 279-292.




DOI: http://dx.doi.org/10.21533/pen.v8i2.1345

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 Azwan Bin Sapit, Saad Kariem Shather, Farook Nehad Abed

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

ISSN: 2303-4521

Digital Object Identifier DOI: 10.21533/pen

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License